This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Find out more here

What is Predictive Maintenance

Mar 08, 2019

This is also known as condition monitoring. It involves monitoring the condition of equipment and detecting defects as they develop.  

There are a number of technologies that can be used such as: vibration analysis, thermal imaging, ultrasound, lubrication analysis, motion amplification and motor testing. The applications used in these technologies to defect faults are called techniques.  

 TECHNOLOGY: Vibration Analysis 

TECHNIQUE: Vibration Analysis, This is trending a piece of equipment over a period of time and then through its vibration patterns detecting defects as they develop. Vibration analysis can be used on rotating equipment where the vibration is reciprocating or it can be used on pipework where the vibration is a little more sporadic. 

TECHNOLOGY: MOTION AMPLIFICATION 

TECHNIQUE:  Motion Amplification:  This is a relatively new version of an old technology. It’s where the number of frames per second (FPS) are altered from the normal 24 FPS (like a movie) and changed to the speed of a machine under inspection. This will amplify the movement of the unit at the relevant speed. Why this technology is so effective is because the software added can use each pixel in the image as a vibration sensors and detected the amount of vibration at that point. This give you the exact RPM and quantifies the vibration. An excellent tool for diagnosis imbalances, misalignments, looseness and other low frequency defects on a machine. 

TECHNOLOGY: Thermal Imaging 

TECHNIQUES: Electrical Thermal Imaging: used for surveying electrical panels to defect bad connections, overloaded circuits, unbalanced phases (where phases should be balanced). Electrical component burnout 

TECHNIQUES: Mechanical Thermal Imaging: Used on motor and other mechanical equipment to detect bearing wear, windings fatigue or other type of destructive rubbing.

TECHNOLOGY: ULTRASONIC 

UltraSonic is sometimes used on its own and also as a combination with other technologies. 

TECHNIQUES: UltraSonic Greasing: This is route based and data collection of ultrasonic levels of the machines. Once a rise in the UltraSonic levels has been detected, the first action would be to lubricate the machine if possible. 
It can then be used when lubricating a unit. The problem with the old method of just pump in a set amount of grease into a bearing is that you don’t know when is it enough, too much or not enough. If you listen to the ultrasonic probe as you lubricate the unit you can keep on pumping unit you hear the noise level drop. Once the level bottoms out this is the adequate level of lubrication need for each bearing. 

TECHNIQUES: UltraSonic of Electrical Panels: Tracking, Arcing and the presents of coronas can be detected using ultrasonic equipment. This is where ultrasonic can be initially used and then other technologies like thermal imaging could then be used for detected exactly where the fault is. UltraSonic of Electrical panels is can be used when panels can’t be opened or can only be opened a small amount. 

TECHNIQUES: Compressed Air leak Detection: some compressed air leaks can be heard when you walk in to a room but other type of leaks can’t be heard with your own ear. This is an easy way of detecting all compress air leaks throughout a plant. Why fix air leak? There are 2 reasons. Air leaks are wasteful expenses because the compressor has to generate the extra air for these leaks and this is see in wasted electricity. Also air leaks can get progressively worse over time. This could lead to process equipment not performing due it pneumatics not operating e.g. actuator valves not opening and closing. 

TECHNIQUES: Steam Traps (moving parts): Detected defects with steam traps is one technique where it’s best to use a few technologies. With the ultrasonic probe you can hear the steam traps operating (opening and closing) or if the strainer is blocked but this can be confirmed using a thermal imaging camera to see the temperature differentials across the trap. Like air leaks there are 2 advantages to detecting faults with steam traps. One is cost savings and the other is if condensate is getting into you steam system it will affect its performance. 

TECHNOLOGY: LUBRICATION ANALYSIS 

TECHNIQUES: Oil Analysis: This is simply taking a sample of oil from a unit and analysing it for degrading of the oil itself and also looking for any impurities such as foreign metal objects or water. Only taking a sample will save on replacing all the oil when there would be no need to, hence saving on the cost of it but more importantly if foreign objects were detected in the sample this would indicate that there is signs of deterioration of the unit itself. This is especially effective in slower moving parts such as gearboxes. The samples will tell you what’s in the oil but the diagnosis of the unit will still be up to the analysis who knows how the unit operates. 

 TECHNOLOGY: ELECTRIC MOTOR TESTING 

TECHNIQUE: Static Motor Testing: This primarily tests the electrical properties of the stator of an AC induction motor and are carried out by a specialist test unit which connects to the motor. Each test increases in magnitude and it is advised for safety reasons to always start at the lowest voltage test and then advance in line with the voltage tests. The first number of tests will indicate if there is a present fault in the motor, however the last tests check the condition of the unit and can indicate of weaknesses are developing. 

Visit our Operations & Maintenance page to find out more information about how LotusWorks support facility owners with knowledgeable, experienced teams or contact us today with your query by clicking here.

Anthony Whitty is a Condition Monitoring Consultant working with LotusWorks.
< Back to Articles


Complete this form to ensure you never miss a LotusWorks blog post
Name: *
Phone: *
Email:*
I consent to receive blog items from LotusWorks
Please tick here
* Denotes required field
GET IN TOUCH
EMAIL: contactus@lotusworks.com
PHONE: +353 (0)71 9169783
Please complete the fields below and we will be in touch...
Join our mailing list for updates & industry news
SEND
© LotusWorks
dmacmedia webdesign